DIVISION 10

MATERIALS

This is the Table of Contents for a Microsoft Word document which can be viewed by clickinghere: div10e.doc. Click on the section number to see a preview in HTML format. The home page for this document is found here.

SECTION 1000 -- PORTLAND CEMENT CONCRETE PRODUCTION AND DELIVERY
1000-1.....DESCRIPTION.
1000-2.....MATERIALS.
1000-3.....PORTLAND CEMENT CONCRETE FOR CONCRETE PAVEMENT.
(A).....Composition and Design:
(B).....Air Entrainment:
(C).....Slump:
(D).....Set Retarding Admixture:
(E).....Water Reducing Admixtures:
(F).....Contractor's Responsibility for Process Control:
(G).....Contractor Not Relieved of Responsibility for End Result:
1000-4.....PORTLAND CEMENT CONCRETE FOR STRUCTURES AND INCIDENTAL CONSTRUCTION.
(A).....Composition and Design:
(B).....Air Entrainment:
(C).....Strength of Concrete:
(D).....Temperature Requirements:
(E).....Elapsed Time for Placing Concrete:
(F).....Use of Set Retarding Admixtures:
(G).....Use of Water Reducing Admixtures:
(H).....Use of Calcium Chloride:
(I).....Use of Fly Ash:
(J).....Use of Ground Granulated Blast Furnace Slag:
1000-5.....CLASS M CONCRETE FOR REINFORCED BRICK MASONRY.
1000-6.....CONCRETE FOR MACHINE PLACED CURB, CURB AND GUTTER, AND PAVED DITCH.
1000-7.....HIGH EARLY STRENGTH PORTLAND CEMENT CONCRETE.
1000-8.....MEASURING MATERIALS.
(A).....Weighing Cement:
(B).....Weighing Aggregates:
(C).....Water:
(D).....Admixture Dispensing Systems:
1000-9.....BATCHING PLANT.
(A).....Bins and Hoppers:
(B).....Scales:
(C).....Water Measuring Devices:
1000-10.....MIXERS AND AGITATORS.
(A).....General:
(B).....Mixer Capacity:
(C).....Agitator Capacity:
(D).....Consistency Tests:
1000-11.....MIXING AND DELIVERY.
(A).....General:
1......Central Mixed Concrete:
2......Transit Mixed Concrete:
3......Shrink Mixed Concrete:
(B).....Mixing Time for Central Mixed Concrete:
(C).....Mixing; Truck Mixers and Truck Agitators:
(D).....Delivery:
1000-12.....CONCRETE PLANT.
SECTION 1005 -- GENERAL REQUIREMENTS FOR AGGREGATE
1005-1.....GENERAL.
1005-2.....HANDLING AND STORING AGGREGATES.
1005-3.....GRADATION.
1005-4.....TESTING.
(A).....General:
(B).....Gradation:
(C).....Liquid Limit:
(D).....Plasticity Index:
(E).....Resistance to Abrasion (Percentage of Wear):
(F).....Soundness:
SECTION 1008 -- AGGREGATE BASE COURSE FOR STABILIZATION
1008-1.....AGGREGATE STABILIZATION
(A).....General:
(B).....Sampling and Acceptance:
(C).....Testing:
(D).....Sampling at the Road:
(E).....Stockpile Sampling:
SECTION 1010 -- AGGREGATE FOR NON-ASPHALT FLEXIBLE TYPE BASES
1010-1.....AGGREGATE BASE COURSE--GENERAL
(A).....General Requirements:
(B).....Testing:
1010-2.....TYPE A AGGREGATE BASE COURSE.
1010-3.....TYPE B AGGREGATE BASE COURSE.
(A).....General:
(B).....Construction of Approved Stockpiles:
(C).....Roadway Sampling:
1010-4.....SOIL TYPE BASE COURSE.
1010-5.....AGGREGATE FOR PLANT MIXED CEMENT TREATED BASE COURSE.
(A).....General
(B).....Approved Stockpile Production
(C).....Quarry production
SECTION 1012 -- AGGREGATE FOR ASPHALT BASES AND PAVEMENTS
1012-1.....AGGREGATES FOR ASPHALT PLANT MIXES.
(A).....Composition of Mixture:
(B).....Coarse Aggregate:
.....(1).....General:
.....(2).....Gradation:
.....(3).....Fractured Faces:
.....(4).....Flat or Elongated Pieces:
.....(5).....Soundness:
.....(6).....Resistance to Abrasion:
.....(7).....Clay Lumps:
(C).....Fine Aggregate:
.....(1).....General:
.....(2).....Natural Sand:
.....(3).....Stone Screenings:
(D).....Mineral Filler:
1012-2.....AGGREGATES FOR ASPHALT SURFACE TREATMENT.
(A).....General:
(B).....Gradation:
(C).....Fractured Faces:
(D).....Soundness:
(E).....Resistance to Abrasion:
(F).....Blending of Aggregates:
(G).....Weight of Slag:
1012-3.....BLOTTING SAND.
SECTION 1014 -- AGGREGATE FOR PORTLAND CEMENT CONCRETE
1014-1.....FINE AGGREGATE.
(A).....General:
(B).....Soundness:
(C).....Deleterious Substances:
(D).....Organic Impurities:
(E).....Mortar Strength:
(F).....Gradation:
(G).....Blending Manufactured Sand:
(H).....Siliceous Particle Content:
1014-2.....COARSE AGGREGATE.
(A).....General:
(B).....Soundness:
(C).....Deleterious Substances:
(D).....Resistance to Abrasion:
(E).....Aggregate Sizes:
.....(1).....General:
.....(2).....Machine Placed Curb, Curb and Gutter, and Paved Ditch:
.....(3).....Prestressed and Precast Concrete:
.....(4).....Use of More Than One Size:
.....(5).....Portland Cement Concrete Pavement:
SECTION 1016 -- SELECT MATERIAL
1016-1.....DESCRIPTION
1016-2.....USES
1016-3.....CLASSIFICATIONS
CLASS I
CLASS II
CLASS III
CLASS IV
CLASS V
CLASS VI
Class VII
SECTION 1018 -- BORROW MATERIAL
1018-1.....GENERAL.
1018-2.....APPROVAL OF BORROW SOURCE.
SECTION 1020 -- ASPHALT MATERIALS
1020-1.....DELIVERY AND ACCEPTANCE OF ASPHALT MATERIALS.
1020-2.....ASPHALT CEMENT.
1020-3.....PRIME COAT MATERIALS
1020-4.....CUT-BACK ASPHALT, RAPID CURING.
1020-5.....CUT-BACK ASPHALT, MEDIUM CURING.
1020-6.....EMULSIFIED ASPHALT, ANIONIC.
1020-7.....EMULSIFIED ASPHALT, CATIONIC.
1020-8.....NON-STRIP ADDITIVE.
1020-9.....WATERPROOFING AND DAMPPROOFING MATERIALS.
(A).....Asphalt Primer:
(B).....Asphalt Cement:
(C).....Cut-Back Asphalt:
(D).....Tar:
(E).....Asphalt Plank:
(F).....Fabric:
SECTION 1024 -- MATERIALS FOR PORTLAND CEMENT CONCRETE
1024-1.....PORTLAND CEMENT.
(A).....General:
(B).....Cement for Class S Concrete:
(C).....Basis of Acceptance, Cast-in-Place Construction:
(D).....Basis of Acceptance, Precast Concrete Products:
1024-2.....AGGREGATE.
1024-3.....ADMIXTURES.
(A).....Basis of Acceptance:
(B).....Approved Sources:
(C).....Air Entraining Agent:
(D).....Chemical Admixtures:
.....(1).....Set Retarding Admixtures:
.....(2).....Water Reducing Admixtures
.....(3).....Calcium Chloride:
(E).....OTHER ADMIXTURES
1024-4.....WATER.
1024-5.....FLY ASH.
1024-6.....GROUND GRANULATED BLAST FURNACE SLAG.
SECTION 1026 -- CURING AGENTS FOR CONCRETE
1026-1.....GENERAL.
1026-2.....LIQUID MEMBRANE CURING COMPOUNDS.
(A).....General:
(B).....Test Procedures:
(C).....Curing Compound for Concrete Pavement & Concrete Shoulder:
1026-3.....POLYETHYLENE FILM.
1026-4.....WATER.
1026-5.....BURLAP.
1026-6.....PAPER BLANKETS.
SECTION 1028 -- JOINT MATERIALS
1028-1.....JOINT FILLER.
1028-2.....RUBBER ASPHALT JOINT SEALER.
1028-3.....PREFORMED NEOPRENE JOINT SEAL.
1028-4.....LOW MODULUS SILICONE SEALANT.
(A).....Silicone Sealant Types:
(B).....The sealant shall meet the following requirements:
(C).....Tests shall be performed in accordance with the following test methods:
1028-5.....BOND BREAKER.
SECTION 1032 -- CULVERT PIPE
1032-1.....CORRUGATED METAL CULVERT PIPE
(A).....GENERAL:
1032-2.....CORRUGATED ALUMINUM ALLOY CULVERT PIPE.
(A).....Corrugated Aluminum Alloy Culvert Pipe:
(B).....Corrugated Aluminum Alloy Flared End Sections:
(C).....Corrugated Aluminum Alloy Pipe Tees and Elbows:
(D).....Acceptance:
1032-3.....CORRUGATED STEEL CULVERT PIPE.
(A).....Corrugated Steel Culvert Pipe and Pipe Arch:
.....1......Coupling Bands:
.....2......Corrugations:
.....3......Elongated Pipe:
.....4......Lifting Straps:
.....5......Coating Repair
.....6......Type IA Pipe:
.....7......Aluminized Pipe:
.....8......Marking Requirements:
(B).....Corrugated Steel Flared End Sections:
(C).....Corrugated Steel Pipe Tees and Elbows:
(D).....Corrugated Steel Eccentric Reducers:
(E).....Acceptance:
1032-4.....COATED, PAVED, AND LINED CORRUGATED STEEL CULVERT PIPE.
(A).....Bituminous Coated Corrugated Steel Culvert Pipe and Pipe Arch:
.....(1).....Type A -- Fully Bituminous Coated:
.....(2).....Type B -- Half Bituminous Coated and Partially Paved:
.....(3).....Type C -- Fully Bituminous Coated and Partially Paved:
.....(4).....Type D -- Fully Bituminous Coated and Fully Paved:
(B).....Bituminous Coated Corrugated Steel Flared End Sections:
(C).....Bituminous Coated Corrugated Steel Pipe Tees and Elbows:
(D).....Bituminous Coated Corrugated Steel Eccentric Reducers:
(E).....Optional Coatings for Bituminous Coated Pipe or Pipe Arch:
(F).....Concrete Lined Corrugated Steel Culvert Pipe:
(G).....Acceptance:
1032-5.....CORRUGATED STEEL STRUCTURAL PLATE PIPE AND PIPE ARCH.
(A).....Acceptance:
1032-6.....CORRUGATED ALUMINUM ALLOY STRUCTURAL PLATE PIPE AND PIPE ARCH.
(A).....Acceptance:
1032-7.....VITRIFIED CLAY CULVERT PIPE.
1032-8 WELDED STEEL PIPE.
(A).....Welded steel pipe shall meet the requirements of ASTM A139 for the grade of pipe called for on the plans.
(B).....Acceptance:
1032-9.....CONCRETE CULVERT PIPE.
(A).....Plain Concrete Culvert Pipe:
(B).....Reinforced Concrete Culvert Pipe:
(C).....Concrete Flared End Sections:
(D).....Concrete Pipe Tees and Elbows:
(E).....Marking:
(F).....Joint Materials:
SECTION 1034 -- SANITARY SEWER PIPE AND FITTINGS
1034- 1.....CLAY PIPE.
1034-2.....POLYVINYL CHLORIDE (PVC) PLASTIC PIPE.
1034- 3.....CONCRETE SEWER PIPE.
1034- 4.....DUCTILE IRON PIPE.
1034- 5.....ACRYLONITRILE-BUTADIENE-STYRENE (ABS) PIPE.
SECTION 1036 -- WATER PIPE AND FITTINGS
1036- 1.....COPPER PIPE.
1036-2.....PLASTIC PIPE
A......Polyvinyl Chloride (PVC) Pipe
B......Polyethylene (PE) Pipe
1036-3.....(VACANT).
1036-4.....STEEL PIPE.
1036-5.....DUCTILE IRON PIPE.
1036-6.....FIRE HYDRANTS.
1036-7.....WATER VALVES.
A......Iron Gate Valves
B......Bronze Gate Valves
1036-8.....MISCELLANEOUS CASTINGS.
1036-9.....ACRYLONITRILE-BUTADIENE-STYRENE (ABS) PIPE.
1036-10.....TAPPING SADDLES, SLEEVES OR VALVES:
A......Tapping Saddles
B......Tapping Sleeves
C......Tapping Valves
1036-11.....CORPORATION AND CURB STOPS.
SECTION 1040 -- MASONRY
1040-1.....BRICK.
1040-2.....CONCRETE BUILDING BLOCK.
1040-3.....CONCRETE PAVING BLOCK.
1040-4.....CEMENT.
1040-5.....HYDRATED LIME.
1040-6.....MORTAR SAND.
1040-7.....WATER.
1040-8.....MORTAR.
1040-9.....GROUT FOR SLOPE PROTECTION PAVING.
SECTION 1042 -- RIP RAP MATERIALS
1042-1.....PLAIN RIP RAP.
1042-2.....FILTER FABRIC.
1042-3.....TESTING.
SECTION 1044 -- SUBSURFACE DRAINAGE MATERIALS
1044-1.....SUBDRAIN FINE AGGREGATE.
1044-2.....PIPE AND FITTINGS--GENERAL.
1044-3.....CONCRETE PIPE AND FITTINGS.
1044-4.....CORRUGATED STEEL PIPE AND FITTINGS.
1044-5.....POLYVINYL CHLORIDE PLASTIC PIPE.
1044-6.....CORRUGATED PLASTIC PIPE AND FITTINGS.
1044-7.....OUTLET PIPE.
SECTION 1046 -- GUARDRAIL MATERIALS
1046-1.....GENERAL.
1046-2.....RAIL ELEMENTS.
1046-3.....POSTS AND OFFSET BLOCKS.
(A).....General:
(B).....Structural Steel Posts:
(C).....Treated Timber Posts:
(D).....Offset Blocks:
1046-4.....HARDWARE.
1046-5.....ANCHORS AND ANCHOR ASSEMBLIES.
1046-6.....REPAIR OF GALVANIZING
1046-7.....ACCEPTANCE
SECTION 1050 -- FENCE MATERIALS
1050-1.....GENERAL.
(A).....Chain Link Fence:
SYSTEM G1:
SYSTEM G2:
SYSTEM G3:
SYSTEM A1:
SYSTEM A2:
(B).....Wire Gage:
1050-2.....TIMBER POSTS AND BRACES.
(A).....General:
(B).....Optional Steel Posts and Braces:
1050-3.....METAL POSTS AND RAILS.
(A).....Chain Link Fence:
(B).....Woven Wire Fence:
1050-4.....BARBED WIRE.
1050-5.....WOVEN WIRE.
1050-6.....CHAIN LINK FABRIC.
1050-7.....FITTINGS AND ACCESSORIES.
1050-8.....REPAIR OF GALVANIZING
SECTION 1052 -- SALT AND LIME STABILIZERS
1052-1.....SODIUM CHLORIDE.
1052-2.....CALCIUM CHLORIDE.
1052-3.....LIME.
(A).....Chemical Requirements:
(B).....Physical Requirements:
.....(1).....Hydrated Lime:
.....(2).....Quicklime:
(C).....Sampling and Inspection:
SECTION 1054 -- MISCELLANEOUS MATERIALS
1054-1.....RIGHT OF WAY MARKERS.
(A).....General:
(B).....Concrete:
(C).....Granite:
1054-2.....PREFORMED BEARING PADS.
1054-3.....DECK DRAINS.
1054-4.....FUNNELS AND FUNNEL DRAINS.
(A).....Funnels:
(B).....Funnel Drain Pipe Elbows and Fittings:
1054-5.....SYNTHETIC ROVING.
1054-6.....GROUT FOR CONCRETE ROADWAY TRAFFIC BARRIER.
SECTION 1056 -- ENGINEERING FABRICS
1056-1.....GENERAL.
1056-2.....PHYSICAL PROPERTIES.
No. .....Method
1056-3.....ACCEPTANCE.
SECTION 1060 -- LANDSCAPE DEVELOPMENT MATERIALS
1060-1.....GENERAL
1060-2.....FERTILIZER.
1060-3.....LIMESTONE.
1060-4.....SEED.
1060-5.....MULCH FOR EROSION CONTROL.
1060-6.....SPRIGS.
1060-7.....SOD.
1060-8.....MATTING FOR EROSION CONTROL.
(A).....General:
(B).....Excelsior Matting:
(C).....Wire Staples:
1060-9.....WATER.
1060-10.....PLANT MATERIALS - NURSERY GROWN.
(A).....General:
(B).....Balled and Burlapped Plants:
(C).....Container Grown Plants:
(D).....Bare Root Plants:
(E).....Plant Substitution:
1060-11.....MULCH FOR PLANTING.
1060-12.....WRAPPING FOR TREE TRUNKS.
1060-12.....MATERIALS FOR STAKING OR GUYING.
(A).....Stakes:
(B).....Wire:
(C).....Hose:
1060-13.....HERBICIDES.
SECTION 1070 -- REINFORCING STEEL
1070-1.....GENERAL.
1070-2.....DEFORMED STEEL BAR REINFORCEMENT FOR STRUCTURES.
1070-3.....COLD DRAWN STEEL WIRE AND WIRE FABRIC.
1070-4.....REINFORCING STEEL BAR SUPPORTS.
1070-5.....PRESTRESSING STRAND.
1070-6.....DOWELS AND TIE BARS FOR PORTLAND CEMENT CONCRETE PAVEMENT.
1070-7.....REINFORCEMENT FOR BLOCK MASONRY.
1070-8.....EPOXY COATED REINFORCING STEEL.
(A).....General:
(B).....Coating Materials:
(C).....Patching Material:
(D).....Reinforcing Steel:
(E).....Surface Preparation of Bars:
(F).....Application of Coating:
(G).....Quality Control Requirements:
(H).....Test Methods Required of the Coater:
(I).....Handling and Identification:
(J).....Fabrication of Steel-Reinforcing Bars After Coating:
(K).....Procedures for Repair of Coating:
(L).....Inspection by the Department:
(M).....Repairs to Coating Due to Loading, Transporting, and Handling:
(N).....Rejection:
SECTION 1072 -- STRUCTURAL STEEL
1072-1.....GENERAL.
(A).....Fabricator Qualification:
(B).....Office:
1072-2.....STRUCTURAL STEEL OF FOREIGN ORIGIN.
1072-3.....FABRICATION OF STRUCTURAL STEEL OUTSIDE CONTINENTAL LIMITS OF UNITED STATES.
1072-4.....SHAPES, PLATES, BARS, AND SHEETS.
1072-5.....BEARING PLATE ASSEMBLIES.
1072-6.....ANCHOR BOLTS.
1072-7.....HIGH STRENGTH BOLTS, NUTS, AND WASHERS.
(A).....General:
(B).....Specifications.
(C).....Manufacturing.
(D).....Testing
(E).....Shipping
(F).....Galvanized High Strength Bolts, Nuts, and Washers:
1072-8.....WELDED STUD SHEAR CONNECTORS.
1072-9.....INSPECTION.
(A).....General:
(B).....Shop and Mill Inspection:
(C).....Sampling Structural Steel:
1072-10.....WORKING DRAWINGS.
1072-11.....HANDLING AND STORING MATERIALS.
1072-12.....STRAIGHTNESS, CAMBER, AND DIMENSIONAL TOLERANCES.
(A).....General:
(B).....Straightening:
(C).....Camber:
(D).....Heat Cambering of Rolled Beams and Welded Plate Girders:
.....(1).....General:
.....(2).....Heat Cambering of Rolled Beams:
.....(3).....Heat Cambering of Welded Plate Girders:
.....(4).....Support of Members for Heat Cambering:
.....(5).....Heating Process and Equipment:
.....(6).....Heat Measurement:
(E).....Camber Measurement:
(F).....Dimensional Tolerances:
1072-13.....OXYGEN CUTTING.
1072-14.....EDGE PLANING.
1072-15.....FACING OR BEARING SURFACES.
1072-16.....ABUTTING JOINTS.
1072-17.....BENT PLATES.
1072-18.....HOLES FOR BOLTS AND OTHER FASTENERS.
(A).....General:
(B).....Punched Holes:
(C).....Reamed or Drilled Holes:
(D).....Subpunching and Reaming of Field Connections:
(E).....Accuracy of Punched and Subdrilled Holes:
(F).....Accuracy of Reamed and Drilled Holes:
(G).....Alternate Methods:
(H).....Oversize, Short-Slotted, and Long-Slotted Holes:
(I).....Misfits:
(J).....Erection Bolt Holes:
1072-19.....INSTALLING BOLTS.
1072-20.....WELDING.
(A).....Definition:
(B).....General:
(C).....Qualification of Personnel:
(D).....Qualification of Welds and Procedures:
(E).....Requirements for Testing and Inspection:
(F).....Nondestructive Test Required:
(G).....Welded Structural Shapes:
1072-21.....SHOP ASSEMBLING.
(A).....General:
(B).....Full Girder Assembly:
(C).....Progressive Girder Assembly:
(D).....Special Complete Structure Assembly:
1072-22.....PAINTING AND OTHER PROTECTIVE COATINGS.
1072-23.....MARKING AND SHIPPING.
SECTION 1074 -- MISCELLANEOUS METALS AND HARDWARE
1074-1.....EXPANSION ANCHORS.
1074-2.....PLAIN STEEL BARS WITH THREADED ENDS.
1074-3.....HARDWARE FOR TIMBER STRUCTURES.
1074-4.....METAL BRIDGE RAILING.
(A).....General:
(B).....Aluminum Rail:
(C).....Galvanized Steel Rail:
1074-5.....STEEL PIPE.
1074-6.....IRON CASTINGS.
(A).....General:
(B).....Gray Iron Castings:
1074-7.....STEPS.
1074-8.....FABRICATED STEEL GRATES.
1074-9.....PINS.
1074-10.....WASHERS.
SECTION 1076 -- GALVANIZING
1076-1.....GALVANIZING.
1076-2.....FABRICATED PRODUCTS.
1076-3.....HARDWARE.
1076-4.....ASSEMBLED PRODUCTS.
1076-5.....SHEETS.
1076-6.....REPAIR OF GALVANIZING.
SECTION 1077 -- PRECAST CONCRETE UNITS
1077-1.....GENERAL.
1077-2.....PLAN REQUIREMENTS.
1077-3.....MATERIALS.
1077-4.....INSPECTION.
1077-5.....PORTLAND CEMENT CONCRETE.
(A).....Composition and Design:
(B).....Testing:
(C).....Temperature requirements:
(D).....Use of Water Reducing Admixtures:
1077-6.....FORMS.
1077-7.....REINFORCEMENT.
1077-8.....PLACING CONCRETE.
1077-9.....CURING CONCRETE.
(A).....General:
(B).....Curing at Elevated Temperatures:
(C).....Water Curing:
(D).....Curing Compound:
1077-10.....LIFT HOLES, HANDLING, TRANSPORTING, AND STORING.
1077-11.....FINAL FINISH.
1077-12.....STEPS FOR PRECAST DRAINAGE STRUCTURES.
1077-13.....MARKING.
1077-14.....DIMENSIONS.
SECTION 1078 -- PRESTRESSED CONCRETE MEMBERS
1078-1.....GENERAL.
1078-2.....MATERIALS.
1078-3.....INSPECTION.
1078-4.....PORTLAND CEMENT CONCRETE.
(A).....Composition and Design:
(B).....Air Entrainment:
(C).....Testing:
(D).....Temperature Requirements:
(E).....Elapsed Time for Placing Concrete:
(F).....Use of Set Retarding Admixtures:
(G).....Use of Water Reducing Admixtures:
(H).....Measuring Materials:
(I).....Mixers and Agitators:
(J).....Mixing and Delivery:
.....(1).....General:
1......Central Mixed Concrete:
2......Transit Mixed Concrete:
3......Shrink Mixed Concrete:
.....(2).....Mixing Time for Central Mixed Concrete:
.....(3).....Truck Mixers and Truck Agitators:
.....(4).....Delivery:
(K).....Read Mixed Concrete Plant:
1078-5.....CASTING BED AND FORMS.
1078-6.....TENSIONING DEVICES.
1078-7.....PLACING STRANDS, TIES, AND REINFORCING STEEL.
1078-8.....TENSIONING PROCEDURE.
1078-9.....PLACING CONCRETE.
1078-10.....CURING CONCRETE.
(A).....General:
(B).....Curing at Elevated Temperatures:
(C).....Water Curing
(D).....Curing with Membrane Curing Compound.
1078-11.....TRANSFER OF LOAD.
1078-12.....PRESTRESSED CONCRETE GIRDER WEB SPLITTING
1078-13.....HANDLING, TRANSPORTING, AND STORING.
1078-14.....FINAL FINISH.
1078-15.....ALIGNMENT AND DIMENSIONAL TOLERANCES.
(A).....Cored Slabs:
(B).....Girders:
(C).....Piles:
(D).....Sheet Piles:
1078-16.....IDENTIFICATION OF MEMBERS.
1078-17.....QUALITY CONTROL.
SECTION 1080 -- PAINT AND PAINT MATERIALS
1080-1.....GENERAL.
1080-2.....PAINT VEHICLES, THINNERS, AND DRIERS.
1080-3.....PACKING AND MARKING.
1080-4.....INSPECTION AND SAMPLING.
1080-5.....RED PRIMER PAINT
1.0.....SCOPE
2.0.....MATERIALS
2.1.....PAINT CHARACTERISTICS:
2.2.....PIGMENT COMPOSITION (% by weight)
2.3.....VEHICLE COMPOSITION (% by weight)
1080-6 ALKYD FINISH PAINT
1.0.....SCOPE
2.0.....MATERIALS
2.1.....PAINT CHARACTERISTICS:
2.2.....PIGMENT COMPOSITION (% by weight)
2.3.....VEHICLE COMPOSITION (% by weight)
1080-7.....SELF CURING INORGANIC ZINC PAINT.
(A).....Composition:
.....(1).....Pigment:
.....(2).....Vehicle:
.....(3).....Properties of Mixed Paint:
(B).....Performance Requirements:
(C).....Color:
1080-8.....COAL TAR EPOXY PAINT.
1080-9.....ZINC RICH PAINT.
1080-10.....WASH PRIMER PAINT.
1080-11.....HIGH BUILD VINYL FINISH PAINT.
(A).....Composition:
.....(1).....Pigments:
.....(2).....Vehicle:
.....(3).....Properties of Mixed Paint:
(B).....Performance Requirements:
(C).....Application Properties:
(D).....Color:
1080-12.....WATERBORNE PRIMER PAINTS.
1.0.....Scope
2.0.....Description
3.0.....Composition
3.1.....Pigment
(% by wt. of paint)
3.2.....Pigments
(% by wt. of pigment)
3.3.....Vehicle (% by wt. of paint
3.4.....Vehicle (% by wt. of vehicle)
4.0.....Paint Characteristics
.....Notes
1080-13.....WATERBORNE FINISH PAINTS.
1.0.....Scope
2.0.....Description
3.0......Composition
3.1.....Pigment (% by wt. of paint)
3.2.....Pigments (% by wt. of pigment)
3.3.....Vehicle (% by wt. of paint)
3.4.....Vehicle (% by wt. of vehicle)
4.0.....Paint Characteristics
.....Notes
1080-14.....PAINT FOR VERTICAL MARKERS
1080-15.....ABRASIVE MATERIALS FOR BLAST CLEANING STEEL.
1080-16.....FIELD PERFORMANCE AND SERVICE.
SECTION 1081 -- EPOXY AND ADHESIVES
1081-1.....EPOXIES - GENERAL.
1081-2.....SPECIFICATIONS FOR USE OF EPOXIES.
(A).....Supply:
(B).....Acceptance:
(C).....Fillers, Pigments, and Thixotropic Agents:
(D).....Shelf life:
1081-3.....NOTES ON USE OF EPOXIES.
(A).....Moisture Conditions:
(B).....Coefficient of Expansion:
(C).....Safety:
(D).....Mixing:
(E).....Storage and Substrate Temperature:
1081-4.....TEST METHODS FOR EPOXIES.
(A) Viscosity:
(B).....Pot Life:
(C).....Compressive Strength of Epoxy Mortar:
(D).....Volatiles Content:
(E).....Ash Content:
(F).....Tensile Strength and Tensile Elongation:
(G).....Hardness:
(H).....Absorption:
(I).....Bond Strength:
1081-5.....PROPERTIES OF EPOXIES.
1081-6.....POLYESTER RESIN EPOXY ADHESIVE.
(A).....General:
(B).....Materials:
(C).....Mixing of Adhesive:
1081-7.....HOT BITUMEN.
(A).....Physical Requirements:
(B).....Test Methods:
.....(1).....Flow
.....(2).....Viscosity
.....(3).....Asphalt Properties
.....(4).....Viscosity Ratio
.....(5).....Filler Material
(C).....Prequalification
(D).....Packaging and Labeling
(E).....Certification
(F).....Application
SECTION 1082 -- STRUCTURAL TIMBER AND LUMBER
1082-1.....UNTREATED TIMBER AND LUMBER.
(A).....General:
(B).....Bearing Piles:
(C).....Sheet Piles:
1082-2.....TREATED TIMBER AND LUMBER.
(A).....General:
(B).....Bridges, Fender Systems, and Piles:
(C).....Guardrail Posts:
(D).....Fence Posts and Braces:
(E).....Sign Posts and Battens:
1082-3.....PRESERVATIVE TREATMENT.
(A).....General:
(B).....Timber Preservatives:
(C).....Bridges, Fender Systems, and Piles:
(D).....Guardrail Posts:
(E).....Fence Posts and Braces:
(F).....Sign Posts and Battens:
SECTION 1084 -- PILES
1084-1.....UNTREATED TIMBER BEARING PILES.
1084-2.....TREATED TIMBER BEARING PILES.
(A).....Timber:
(B).....Preservative Treatment:
1084-3.....STEEL BEARING PILES.
1084-4.....STEEL PILE SHELLS.
(A).....General:
(B).....Cylindrical Steel Pipe:
(C).....Fluted Tubular Steel:
1084-5.....PRESTRESSED CONCRETE BEARING PILES AND SHEET PILES.
1084-6.....UNTREATED TIMBER SHEET PILES.
1084-7.....TREATED TIMBER SHEET PILES.
(A).....Timber:
(B).....Preservative Treatment:
1084-8.....STEEL SHEET PILES.
SECTION 1086 -- PAVEMENT MARKERS
1086-1.....TEMPORARY RAISED PAVEMENT MARKERS
(A).....General:
(B).....Adhesives:
.....(1).....Epoxy:
.....(2).....Hot Bitumen:
.....(3).....Pressure Sensitive:
(C).....Material Certification:
(D).....Approval:
1086-2.....PERMANENT RAISED PAVEMENT MARKERS.
(A).....General:
(B).....Hot Bitumen Adhesives:
(C).....Material Certification:
(D).....Approval:
1086-3.....SNOWPLOWABLE RAISED PAVEMENT MARKERS
(A).....General:
(B).....Castings:
.....(1).....Dimensions:
.....(2).....Materials:
.....(3).....Surface:
.....(4).....Identification:
(C).....Reflectors:
.....(1).....General:
.....(2).....Reflector Type:
.....(3).....Reflector Optical Requirements:
a......Definitions
b......Optical Performance
(D).....Physical Properties:
.....(1).....Strength Test:
.....(2).....Impact Test:
.....(3).....Temperature Cycling Test:
(E).....Epoxy Adhesives:
(F).....Material Certification:
(G).....Approval:
SECTION 1087 -- PAVEMENT MARKINGS
1087-1.....GENERAL.
1087-2.....COMPOSITION.
(A).....Paint Composition:
(B).....Removable Tape Composition:
(C).....Thermoplastic Composition:
(D).....Epoxy Composition.
(E).....Cold Applied Plastic Composition:
1087-3.....COLOR.
1087-4.....GLASS BEADS
(A).....Composition
(B).....Physical Characteristics
(C).....Gradation
1087-5.....PACKAGING FOR SHIPMENT
1087-6.....STORAGE LIFE.
1087-7.....TESTS TO BE PERFORMED.
(A).....Tests:
(B).....Material Certification:
(C).....Approval:
SECTION 1088 -- DELINEATORS
1088-1.....REFLECTIVE UNIT REQUIREMENTS FOR DELINEATORS
(A).....Definitions:
(B).....Reflective Elements:
.....(1).....Prismatic Plastic Type:
(a).....General:
(b).....Specific Intensity:
(c).....Durability:
.....(2).....High Performance Sheeting Type:
.....(a).....General:
.....(b).....Sheeting Durability:
1088-2.....GUARDRAIL AND BARRIER DELINEATORS.
(A).....Brackets and Casings for Delineators:
(B).....Reflective Element Requirements:
(C).....Material Certification:
(D).....Approval:
1088-3.....GUARDRAIL END DELINEATION.
(A).....General:
(B).....Reflective Unit Requirements:
(C).....Material Certification:
(D).....Approval:
1088-4.....(VACANT)
1088-5.....OBJECT MARKERS.
(A).....General:
(B).....Reflectors:
(C).....Reflective Sheeting Requirements:
(D).....Panel Requirements:
(E).....Fasteners:
(F).....Material Certification:
(G).....Approval:
1088-6.....MINI DRUM DELINEATORS.
(A).....General:
.....(1).....Casing:
.....(2).....Mounting Hardware:
(B).....Reflective Unit Requirements:
(C).....Material Certification:
(D).....Approval:
SECTION 1089 -- TRAFFIC CONTROL
1089-1.....WORK ZONE SIGNS.
(A).....General:
(B).....Material Certification:
(C).....Approval:
1089-2.....BARRICADES.
(A).....General:
(B).....Supports:
(C).....Reflective Sheeting:
(D).....Material Certification:
(E).....Approval:
1089-3.....CONES.
(A).....General:
(B).....Ballast:
(C).....Retroflective Collars:
(D).....Material Certification:
(E).....Approval:
1089-4.....DRUMS
(A).....General:
(B).....Body:
(C).....Reflective Stripes:
(D).....Ballast:
.....(1).....Sandbag Ballast Method
.....(2).....Tire Sidewall Ballast Method
(E).....Material Certification:
(F).....Approval:
1089-5.....FLASHING ARROW PANELS.
(A).....General:
(B).....Material Certification:
(C).....Approval:
1089-6.....CHANGEABLE MESSAGE SIGNS.
(A).....General:
(B).....Power Source:
(C).....Panel Support:
(D).....Control Systems:
(E).....Message Sign Panel:
(F).....Memory:
(G).....Material Certification:
(H).....Approval:
1089-7.....TEMPORARY CRASH CUSHIONS.
(A).....General:
(B).....Reflective End Treatments:
(C).....Material Certification:
(D).....Approval
1089-8.....TRUCK MOUNTED IMPACT ATTENUATORS.
(A).....General:
(B).....Crash Tests:
(C).....Other Tests:
(D).....Reflective End Treatment:
(E).....Material Certification:
(F).....Approval:
1089-9.....WARNING FLAGS
(A).....General:
(B).....Flag Material:
.....(1).....Fabric Type Flags
.....(2).....Panel Type Flags
(C).....Reflective Sheeting:
(D).....Material Certification:
(E).....Approval:
1089-10.....WARNING LIGHTS
(A).....General:
(B).....Lamp and Enclosure Lens:
(C).....Visibility:
(D).....Power:
(E).....Material Certification:
(F).....Approval:
1089-11.....FLAGGER.
(A).....Reflective Sheeting:
(B).....Material Certification:
1089-12.....WORK ZONE ASPHALT ISLAND.
(A).....General:
(B).....Tubular Markers.
(C).....Paint Requirements:
(D).....Approval:
SECTION 1090 -- PORTABLE CONCRETE BARRIER
1090-1.....PORTABLE CONCRETE BARRIER.
(A).....General:
(B).....Used Portable Concrete Barrier:
(C).....Anchor Bolts:
(D).....Anchor Bolt Adhesives:
(E).....Approval:
SECTION 1092 -- SIGNING MATERIALS
1092-1.....SIGNS AND HARDWARE.
1092-2.....RETROREFLECTIVE SHEETING.
(A).....General Requirements:
(B).....Patching:
1092-3.....BUTTON-TYPE DEMOUNTABLE COPY.
1092-4.....CERTIFICATION.
1092-5.....VERY HIGH BOND TAPE
SECTION 1093 -- RETROREFLECTIVE SHEETING
1093-1.....GENERAL.
1093-2.....PHYSICAL REQUIREMENTS.
(A).....Color Requirements:
(B).....Specific Intensity Per Unit Area (SIA):
(C).....Specular Gloss:
(D).....Color Processing:
(E).....Shrinkage:
(F).....Flexibility:
(G).....Adhesive:
(H).....Impact Resistance:
(I).....Accelerated Weathering:
(J).....Colorfastness:
(K).....Fungus Resistance:
1093-3.....CERTIFICATION.
SECTION 1094 -- GROUND MOUNTED SIGNS
1094-1.....GROUND-MOUNTED SIGN SUPPORTS.
(A).....Breakaway or Simple Steel Beam Sign Supports:
(B).....3-Lb. Steel U-Channel Posts:
(C).....2-Lb. Steel U-Channel Posts:
1094-2.....RIVETS FOR SIGN OVERLAYS.
SECTION 1096 -- OVERHEAD SIGN ASSEMBLIES
1096-1.....ALUMINUM OVERHEAD SIGN ASSEMBLIES.
1096-2.....STEEL OVERHEAD SIGN ASSEMBLIES.
1096-3.....WELDING.
SECTION 1097 -- OVERHEAD SIGN LIGHTING SYSTEMS.
1097-1.....ELECTRICAL INDUSTRY STANDARDS.
1097-2.....MERCURY VAPOR LUMINARIES.
1097-3.....LAMPS.
1097-4.....FORMED CHANNEL.
1097-5.....CONDUIT, BOXES, AND FITTINGS.
1097-6.....WIRE AND CABLE.
1097-7.....POLES.
1097-8.....SWITCHES.
1097-9.....CIRCUIT BREAKERS AND PANELS.
1097-10.....PHOTOCELL CONTROLLERS.
1097-11.....CONTACTORS.
1097-12.....TRANSFORMERS.
1097-13.....ENCLOSURES.
1097-14.....LOCKS.
1097-15.....STRAPPING AND HARDWARE.
1097-16.....GROUNDING AND BONDING EQUIPMENT.